Sending an e-mail via Telnet

In this document, we:

• shall use Telnet to connect to the SMTP server.
• shall give commands to the server, then type our e-mail, and finally tell the server, 'Okay, the e-mail is done. Send it.
• can then send more mails, or disconnect from the server.

The steps are quite similar to what you do when you send an e-mail from - for instance - Outlook Express. We are going to use the SMTP server of monitortools.com with the ID 'webmaster'.

Step 1

Connect to the Internet in case you are a dial-up user. Open an MS-DOS prompt, and enter this command:

C:\WINDOWS>telnet mail.monitortools.com 25

This will open a Telnet window, and within a short time, you will be connected to the SMTP server, and the server says:

220 PROTAGONISTNT Mailmax version 4. 8. 3. 0 ESMTP Mail Server Ready

This varies, but you should definitely see the '220' part. It is an indication that the server is ready to service your request.

Step 2

Now the server expects you to identify yourself. If you are a dial-up user, you can enter the name of your computer (the one Windows asks you when you intall Windows) or anything else you want. If you have a domain-name, then you should enter the domain-name here. My computer's name is dell01, so I say:

helo dell01

Note that it is 'helo' and not 'hello'. The commands are not case-sensitive, so you can also say HeLo or HELO or hELo. The server replies:

250 HELO 217.120.215.201, How can I help you?

This is like a shake-hand. You tell the server your name, and it says its name! Computers are quite friendly, you see!

Step 3

Next give the server your e-mail address. Note that most SMTP servers require that your e-mail address belong to the same domain as the server. For example, if you send mail from Yahoo! SMTP server, you should have a Yahoo! address. You cannot use it if you give it a Hotmail address. Let me give the SMTP server some e-mail address:

mail from: Ten adres pocztowy jest chroniony przed spamowaniem. Aby go zobaczyć, konieczne jest włączenie w przeglądarce obsługi JavaScript.

'mail from:' is a SMTP command. Note that there is a space between 'mail' and 'from', followed by a colon (:). The server says:

250 Ok

Step 4

Tell the server who you want to send the e-mail to. Let me send a mail to info@activexperts:

rcpt to: Ten adres pocztowy jest chroniony przed spamowaniem. Aby go zobaczyć, konieczne jest włączenie w przeglądarce obsługi JavaScript.

There are no restrictions here. You can enter any e-mail address. If there is some problem with the recipient-address, your mail will bounce, but for now, the server doesn't complain. It will say:

250 Ok

Step 5

You have told the server your e-mail address, and the recipient's e-mail address, so now you can go ahead and type the e-mail. You have to do that with the data command:

data

The server asks you to go ahead with your e-mail:

354 End data with .

Don't worry with the thing. It'll be explained later.

Step 6

Now type in your e-mail, like this:

This is a test e-mail.
Remember to type it all right. Backspace key doesn't work in Windows
Telnet, though it does in Linux. If you make a mistake, try pressing
CTRL-h. If it works, well and good.

When you finish your e-mail, press [ENTER], then a '.', and again an [ENTER]. This tells the server that you have finished the e-mail, and it can send it. It will say:

250 Ok: queued as 6AB5150038

Your mail was sent!

Step 7

Now you can either send another mail, or disconnect from the server. If you want to send another mail, you should repeat the 'rcpt to:' and 'data' commands. There is no need for 'helo' and 'mail from:', because the server already knows who you are. If you want to disconnect, just say 'quit':

quit

The server will reply:

221 Bye

and you will lose connection with the server. Hurray, you sent a mail direct from the server! Try this in front of your friends who may be used to only GUIs and icons. They will begin to call you up for technical support!